Skip to content
Home // Articles // Chain Grate Stoker Burnout: Causes, Case Study, and Practical Solutions
Company News

Chain Grate Stoker Burnout: Causes, Case Study, and Practical Solutions

xw 20250813103243
Understanding and resolving common chain grate stoker burnout issues in industrial boilers

Chain grate stokers are essential components of industrial boilers, responsible for stacking solid fuel and enabling efficient combustion. The horizontal chain grate stoker consists of alternating fixed boiler grate bars and movable heating furnace grate bars, with each set of grate bars positioned on the same plane.

While their advantages include low fuel quality requirements and automatic fire management, significant drawbacks exist. During regular industrial boiler inspections, we frequently encounter severe burn-through and deformation of horizontal grates, with some requiring replacement after just a few months of operation. These issues directly impact production efficiency.

Chain Grate Stoker Burnout: Causes, Case Study, and Practical Solutions

Case Study: SZL10-1.0-AII Industrial Steam Boiler

This boiler plant was manufactured in December 2019 and began operation in December 2021. All pre-commissioning instrument checks indicated good furnace condition and normal stoker operation. After two years of operation, significant grate problems emerged.

Extensive burn deformation severely affected production, with the shortest replacement interval being just three months. Upon inspection, removed grate fragments showed severe corrosion, with some grate bars reduced to just 2/3 or less of their original length.

Chain Grate Stoker Burnout: Causes, Case Study, and Practical Solutions

Factors Affecting Chain Grate Stoker Burnout

1. Fuel Selection

Chain grate stokers are suitable for medium-low volatile bituminous coal, inferior coal, lignite, and biomass fuels with low calorific value (below 5000 kcal/kg).

The coal used in this case had a calorific value of about 5500 kcal/kg, which is too high for horizontal chain grate stokers. Certain coals like coking coal, gas coal, lean coal, and lignite tend to cake easily, exacerbating grate problems.

2. Chain Grate Stoker Design

The design significantly impacts fuel combustion through several aspects:

  • Grate bar material: The RQTAI5Si heat-resistant cast iron specified wasn’t used – instead IT150 material was substituted, which cannot withstand the maximum working temperature of 900°C.
  • Grate bar size: While geometric dimensions and overlapping methods met specifications, material issues remained problematic.
  • Ventilation: Proper spacing between grate bars and moderate coal particle size are crucial to prevent carbon particle blockage that hinders cooling.

3. Grate Bar Manufacturing Process

While current casting technology achieves good yields with smooth surfaces free of defects like blowholes, material selection remains critical for longevity.

4. Boiler Operation Management

Several operational factors contribute to grate burnout:

  • Improper coal bed thickness and stoker travel speed
  • Failure to promptly remove fine ash accumulation in air chambers
  • Poor grate ventilation due to excessive coal bed density
  • Inadequate ventilation in high-temperature zones
  • Excessive furnace positive pressure or strong arch reflection
  • Improper shutdown procedures allowing coal to burn on the grate

Chain Grate Stoker Burnout: Causes, Case Study, and Practical Solutions

Root Causes of Grate Burnout

Three primary factors were identified in this case:

  1. Incorrect grate bar material selection (failure to use RQTSi5 material in main combustion zones)
  2. Long-term positive pressure combustion affecting primary air and grate cooling
  3. Excessive temperature at the coal-grate contact point due to poor cooling

These issues created a vicious cycle that significantly shortened grate lifespan and caused unnecessary economic losses.

Chain Grate Stoker Burnout: Causes, Case Study, and Practical Solutions

Recommended Solutions

  1. Replace main combustion zone grate bars with RQTSi5 material to improve heat resistance
  2. Use bituminous coal with lower calorific value (~4000 kcal/kg)
  3. Mix coal with slag or use coal blends to improve combustion and maintain negative pressure operation
  4. Ensure proper grate cooling through optimal coal bed thickness and stoker travel speed

Implementing these measures will extend grate lifespan and ensure safe, stable boiler operation.

Chain Grate Stoker Burnout: Causes, Case Study, and Practical Solutions

About RKO Boiler

RKO Boiler (Zhengzhou RKO Energy Technology Co., Ltd.) is a Chinese industrial boiler manufacturer supplying Asia, Africa and the Middle East and Asia, Africa and the Middle East. Our team is dedicated to providing economical, reliable steam boiler solutions for various industries.

For more technical information and boiler solutions, visit our website: www.rkoboiler.com

 

Share: WhatsApp Facebook
YX
RKO Boiler engineering team

Technical team supporting capacity calculations, boiler selection and maintenance planning for industrial plants in Asia, Africa, the Middle East and Latin America.

Also read

More articles

All articles →
Technical consultation

Have a question about this guide?

Tell us about your plant conditions. We will translate the process requirement into a sensible boiler specification.

WhatsApp Email Contact